WRXLink V11 - WRX11X

£1,475.00

Easy to install. Affordable. Reliable.

G4X PlugIn ECUs offer the latest in engine management technology, designed to easily maximize the potential from your car. This ECU fits inside the factory OEM enclosure. Installation of processing unit is a breeze, with no alteration of the factory wiring loom required for the models listed below. 

Due to the amount of variation on this vehicle, please ensure you read the Configuration - Memo Text in PCLink.

This product supports the following models:

  • 2007-2014 WRX and WRX STI with GR/GV/GH/GE chassis codes, for JDM/AUDM/SADM/EURO markets, with turbocharged EJ20 or EJ25 engines.

  • 2008-2010 USDM models which have the common international Denso ECU Pinout**

  • 2015-2021 WRX STI with VAB/VAF chassis codes, for JDM/AUDM/SADM/EURO markets, with turbocharged EJ20 or EJ25 engines

**Note: Refer to the supported models document below for more detail. 2011 and later USDM models are supported by our WRX11 USDM ECU

Note: This Plug-in features a new 4 pin powered CAN connector and cannot use the old CANPCB cable for CAN connection.  Use the CANJST4 (Link PN 101-0198) cable for connecting CAN devices.  This new 4 pin port and cable provide not only the CAN connection, but also a protected 12V power supply and ground for powering the CAN devices.  The power supply is protected by a self-resetting fuse rated at 3A continuous.

Easy to install. Affordable. Reliable.

G4X PlugIn ECUs offer the latest in engine management technology, designed to easily maximize the potential from your car. This ECU fits inside the factory OEM enclosure. Installation of processing unit is a breeze, with no alteration of the factory wiring loom required for the models listed below. 

Due to the amount of variation on this vehicle, please ensure you read the Configuration - Memo Text in PCLink.

This product supports the following models:

  • 2007-2014 WRX and WRX STI with GR/GV/GH/GE chassis codes, for JDM/AUDM/SADM/EURO markets, with turbocharged EJ20 or EJ25 engines.

  • 2008-2010 USDM models which have the common international Denso ECU Pinout**

  • 2015-2021 WRX STI with VAB/VAF chassis codes, for JDM/AUDM/SADM/EURO markets, with turbocharged EJ20 or EJ25 engines

**Note: Refer to the supported models document below for more detail. 2011 and later USDM models are supported by our WRX11 USDM ECU

Note: This Plug-in features a new 4 pin powered CAN connector and cannot use the old CANPCB cable for CAN connection.  Use the CANJST4 (Link PN 101-0198) cable for connecting CAN devices.  This new 4 pin port and cable provide not only the CAN connection, but also a protected 12V power supply and ground for powering the CAN devices.  The power supply is protected by a self-resetting fuse rated at 3A continuous.

CAN Lambda (CANLAM)
CAN Lambda (CANLAM)
£310.00
XS Expansion Loom (XSL)
XS Expansion Loom (XSL)
£35.00
CANJST - CAN Connection Cable for Plugin ECU's ( Options )
CANJST - CAN Connection Cable for Plugin ECU's ( Options )
£29.00
ECU Connection:
Link MAP Sensor ( Options )
£100.00
Operating Range:

Important Notes

  • Please check your connector matches the header in the listed photo before purchasing. 

  • This ECU works for manual transmissions only.  

  • Air temp sensor highly recommended. 

  • Most factory features are supported including DCCD, hill start assist, SI drive, cruise control, cam control & ABS supported. 

  • Check the features tab for I/O input & output expansion options.

  • The security/immobiliser lamp may remain illuminated in some models

Take a look at our supported models list to find out which models are supported and which are not. Alternatively, contact your LinkECU Reseller or our 24/6 Tech Support Team.

G4X PlugIn Key Features (where applicable):


Up to 6D fuel and ignition mapping 
Precision closed loop cam control (four cam, independent control) 
Sequential fuel delivery 
Digital triggering, all OEM patterns 
OEM idle hardware supported 
5D boost control with three switchable tables 
Motorsport features - antilag, launch, flat shift 
Continuous barometric correction (on board) 
CAN port 
QuickTune - automated fuel tuning 
Individual cylinder correction 
USB tuning cable included 
Stats recording into on-board memory 
Gear compensations for spark, boost and fuel 
Real time selectable dual fuel, ignition and boost maps 
Sync and crank sensors can be a combination of Hall effect, variable reluctance or optical 
Boost control referenced to gear, speed or throttle position 
512 mega bytes data logging memory within storage unit 
Staged injection 
Knock with "windowing" 

I/O Options:


The following expansion connector inputs/outputs are provided:  
Expansion connector 1   
Pin 1                Aux 16 
Pin 2                DI 11 
Pin 3                An Temp 4 
Pin 4                Knock 2 
Pin 5                Injector 6 

DOWNLOAD MANUAL HERE

You Might Also Like